Skip to content

Tech pack checklist: the ten parts a factory needs

By UniformsOS Team. Updated .

The ten parts

Part The question it answers
1. Cover page What is this, and which version am I holding?
2. Flat sketches What does it look like from every side?
3. Bill of materials What is it made of?
4. Measurement chart How big is each size, and how exact must it be?
5. Construction details How is it sewn?
6. Colorways Which colors go where?
7. Artwork placement Where do logos, names and numbers sit, and how big are they?
8. Labels What labels go in, and where?
9. Packing How is it folded, bagged and boxed?
10. Revision history What changed, when, and who approved it?

1. Cover page

Style number, style name, season or date, size range, the brand or customer, your contact and the version number. Put the style number and version on every page after it as well. Pages get separated.

2. Flat sketches

Line drawings of the garment laid flat: front, back and, if it matters, the side. Add close-ups of anything unusual, such as a collar, a pocket or a vent.

Sketches are drawings, not fashion illustrations. No body, no shading. Show every seam and every line of topstitching, because the factory will sew what it sees.

3. Bill of materials

Every physical thing that goes into one piece.

Item What to specify
Main fabric Fiber content, knit or weave, weight in GSM, color
Secondary fabrics The same, plus where each one goes
Thread Type and color, for needles and loopers
Trims Elastic, drawcords, buttons, zippers, with sizes
Labels Brand, size, care and content
Packaging Bag, sticker, hangtag

See the jersey fabric guide for what the fabric line should say.

4. Measurement chart

The part factories use most. It lists each point of measure, how it is taken, the value for every size and the tolerance.

Typical points of measure for a jersey:

  • Chest width, one inch below the armhole
  • Body length, from the high point of the shoulder
  • Shoulder width
  • Sleeve length
  • Sleeve opening
  • Neck width and neck drop
  • Hem width

Two things are missing from most charts.

Tolerances. No factory hits a number exactly. State how far off is acceptable, such as half an inch on body length and a quarter inch on a neck opening. Without a tolerance, every measurement dispute is an argument.

Grading. The chart must give every size, not one sample size with "grade accordingly". The step between sizes is your decision, not the factory's.

5. Construction details

For every seam and hem: the stitch type, the seam allowance and the stitches per inch. Name stitches by class number, such as 514 for a four-thread overlock, so there is one reading. Stitch types in sportswear lists them.

Add hem depths, needle spacing for coverstitching and any reinforcement, such as bartacks at stress points.

6. Colorways

A table of every color version: which color goes on which part. Give colors as references from a color system, not as words. "Navy" is twenty different colors.

For sublimated products, the color standard is an approved test print on the production fabric. Keep it, and name it in the tech pack.

7. Artwork placement

For each logo, name and number: the size, and the position measured from a fixed point on the garment. "Front number, 8 inches tall, centered, top edge 3 inches below the neck seam" can be checked with a tape. "Centered on chest" cannot.

Say what happens across sizes. Either the artwork scales with the garment, or it stays one size and the position moves. Both are common. The factory needs to know which.

8. Labels

List each label, its content and where it is sewn or printed.

In the United States, the Federal Trade Commission requires most clothing to carry a label with the fiber content, the country of origin and the identity of the manufacturer or another business responsible for it. Care instructions go on a permanent label. Check the rules for every country you sell in before you finalize this page.

9. Packing

How each piece is folded, what bag it goes in, what the sticker says, how many go in a carton and how the carton is marked. For team orders, say whether pieces are packed by size or by player.

10. Revision history

A table at the back: date, what changed, who approved it. Raise the version number with every change and send the whole document again, not a note about the change.

There must be one current version. Put the version in the file name. When a factory makes the old version, the first question will be which one it was sent.

For custom teamwear

A team dealer does not write a new tech pack for every order. The tech pack describes the style: the cut, the fabric and the construction. It is written once.

Each order then adds an order sheet: the team's approved artwork, the roster with sizes, names and numbers, and the ship-by date. Keeping the two apart is what lets one style serve hundreds of teams.

The gaps factories complain about

  • No tolerances.
  • One size specified and the rest left to the factory.
  • A front sketch only.
  • Colors given as names.
  • Artwork with no dimensions.
  • Three versions in the same email thread.

Test it before you send it

Give the tech pack to someone who has not worked on the product. Ask them to write down every question they would need answered before making it. Each question is a gap. Close them and the factory will not have to ask.

Tech packs in UniformsOS

In UniformsOS a tech pack is a file attached to the order. When the order goes to a factory, the file is copied onto that factory's purchase order in Manufacturers and Vendors, next to each line's SKU, decoration, color and sizes from the product record.

FAQ

What is a tech pack?
The document that tells a factory exactly how to make a garment: sketches, materials, measurements for every size, construction, colors, artwork placement and labels.
Who makes the tech pack?
The brand or dealer that owns the product, or a product developer working for it. If a factory writes it for you, get a copy. Without one you cannot move the product to another factory.
What is the difference between a tech pack and a spec sheet?
A spec sheet is the measurement chart. It is one part of a tech pack.
Do sublimated jerseys need a tech pack?
Yes, for the cut, fabric and construction. The printed design is handled separately on each order.
How detailed should a tech pack be?
Detailed enough that a factory could make the product without asking you a question.

Sources

Try UniformsOS free for 30 days

30-day free trial, every module on, no card needed.

All articles